HAUS PLANS ®️
HAUS PLANS ®️Video
- Format:
- YouTube channel
- New videos:
- Several times a week
- Typical length:
- about 1 minute
- Latest video:
About this show
Construction Content General Contractor 20+ Years Collab: info@hausplans.com https://creators.homedepot.com/mypage/hausplans
Videos come from the channel's public YouTube feed. The artwork is the newest video thumbnail. Last updated . Names, artwork and text belong to their publishers.
Cosmos
Similar by topic and creator
- RezzyCarz
Shares the topic How-To and DIY. - Garden Answer
Shares the topic How-To and DIY. - Satori Graphics
Shares the topic How-To and DIY.
Videos
Making a Massive Smash Burger with Construction Toold
· 57 sec
We attempted to make a massive smash burger using construction tools. First, we used 9 pounds of ground beef and covered it with white onions. Next, I had a giant smasher attachment fabricated for the skids steer- this worked awesome. For seasoning- just a dash of salt and pepper. I can’t evening describe to you how good this burger smelled as it started fry- 18” of deliciousness. After about 10 minutes it was time to flip this bad boy, which was a lot harder than it looks because it was so big and heavy. Next up we added the best cheese money can buy, American Cheese. No store sells buns this big, so we made our own. Time to put it together. Once I got the burger on the bun it was time for the special sauce. Check out that sauce distribution – just like putting down subfloor adhesive. Boom, look at the size of this thing! My only regret with this burger is that I didn’t make it a double. Let us know what should we make next? @hausplans #construction #heavyequipment #cooking #diy #contractor
Not rated yetLumber’s Not Getting Any Straighter- Here’s a Fix
· 1 min
I don’t know if you’ve noticed but lumber’s not getting any straighter Here’s how to fix a crooked stud without replacing it using a scrap piece of wood and deck screws. First, I cut a 1 ½” by 3 ½” notch in the crooked stud. I set the depth on my circular saw and cut the bottom and top. Then I use my multi-tool for the vertical cut- I make sure to keep the blade moving. Now you’re probably asking- why did you use a crooked stud? We pick through and use straight studs to start with, but there’s always a few that go crooked as they dry out. Next, I put my scrap piece of wood into the notch that I cut and attach it to the stud on either side - I use two deck screws in each stud. Now this is a non-load bearing wall, so it’s ok to notch out an inch and a half. I mark the center on the scrap wood and start two screws; then I pull the crooked stud into place. Here’s the cool part- watch how the screw pulls the stud forward. Now, this stud is plumb right to left and in and out. Let me know if you think this is the smartest thing you’ve ever seen. @hausplans #build #howto #construction #contractor #hack
Not rated yetThis Won’t Pass Inspection- I Made a Fireblocking Mistake
· 1 min
This will definitely fail inspection, why? Because it’s not fire blocked. We framed a chase around this radon pipe, and the top is completely open. If a fire started inside the chase, it could easily spread to the attic. I’m going to use this scrap piece of 5/8” ZIP roof sheathing to seal off the top. Residential code allows fire blocking with wood- but I did make a mistake here so I will tell you what I did wrong later. I want to get the wood as tight as possible around the pipe. This shape is great for me because I have such big arm muscles. First, I need to install this piece of 2x4, so the top framing is all even. Then I can set my piece on top and slide it into place- fits like a glove. But if you look close there’s still a small gap around the pipe. I’m going to use a fire block foam sealant to seal it up. Now that the top is sealed off I’ve reduced airflow and drafts- this will help to impede the spread of fire. As for the mistake I made- code requires sheathing being used for fire blocking to be 23/32”- the 5/8s ZIP is too thin; so tomorrow I’ll be adding a piece of ¾” plywood underneath to make it right. @hausplans #build #howto #construction #diy #contractor
Not rated yetDon’t Build on Fill Dirt — Do This First
· 1 min
Have you guys tried the new McSlurry? It’s absolutely delicious! Actually, I’m using slurry to solve a big problem on the shop we’re building. Everything above this orange line is fill the last owner dumped here, and fill settles. So, we dug all the way down to original dirt and had it inspected. Now we need to build back up. Instead of filling the entire footing with concrete, we’re using a flowable fill- also called “slurry”. It’s a runny mix of water, sand, fly ash, and just a little cement. And watch this- it levels itself and flows right where it needs to go- no raking and no vibrating. It’s not as strong as concrete, but once it cures it’s harder than the original dirt. Then we pour a 10” concrete footing with rebar right on top. A lot of builders would have built this building on top of the fill dirt, but I’d rather dig down to original dirt, pour the slurry, and know it’s not going anywhere. So what do you think? Was digging down a waste of money or cheap insurance from future problems? @hausplans #build #howto #construction #diy #contractor
Not rated yetMaking a Massive Candy Bar With Construction Tools #sponsored @5hourenergyshot
· 55 sec
We attempted to make a massive candy bar with construction tools. #sponsored @5hourenergyshot #5hourambassador I used a wrecking ball to smash up peppermint sticks. Then I shoveled all the shatter pieces into our four-foot pan. Next, we put a layer of marshmallows over top of the peppermint. I dumped a 5-gallon bucket of chocolate chips straight into the excavator bucket. We used a propane torch to heat the bucket so the chocolate would melt. Then we poured in 5-hour ENERGY Peppermint Mocha shots to give the chocolate a cool peppermint and rich mocha flavor. I spread an even layer of chocolate into the pan with the excavator and used a concrete float to smooth it out. We set the pan in ice till the chocolate was rock hard. This is where things got tricky- we put a board on top and carefully flipped the pan upside down. It looked so good- I couldn’t wait to cut a piece. I think this is my new favorite dessert. Let us know- what should we make next on the jobsite? @hausplans #construction #heavyequipment #cooking
Not rated yetTrying to Pull $1,000 of Wire Out of the Ground
· 1 min
I’m trying to pull a thousand dollars’ worth of wire out of the ground, but here’s the problem- it won’t budge. So, I’m going to try to hook on to it with this ratchet strap and pull it out with my skid steer. This type of knot will only get tighter as I pull. Then I loop the strap around the wires two more times. Honestly, I’m not an electrician and I had no idea if this would work. This wire ran to a trailer that’s no longer on the property, but I want to see if I can save it. Tomorrow we’re gonna dig footings in this area for a new shop, so I want to get the wire out before we tear it up. I was surprised it actually started out working really well. This wire is aluminum not copper, and I estimated that it’s 200 feet long, Then just like that, it got hung up on something. I tried pulling a little harder and the strap broke. I have no idea what it got hung up on, but since it was almost all the way out; I decided just to cut it off. Now I did some research-- brand new, this wire would cost around 1,000 bucks. It could be reused, but how much do you think I would get for it as scrap? @hausplans #build #howto #construction #diy #contractor
Not rated yetI Tore Down a Building With My Homemade Wrecking Ball
· 1 min
I just made a 700-pound wrecking ball in my garage, and I’m going to use it to demo a building. I made this wrecking ball by cutting the top off an ocean buoy and filling it with concrete so I couldn’t wait to see what it would do. Normally wrecking balls are swung from a giant crane, but I’m gonna use this excavator instead. Right off I was blown away with how much power it has- when this thing is swinging it has a crazy amount of momentum. The weight from the wrecking ball was jerking the excavator around a little bit- so I was careful not to swing it too hard. Next time I’ll get a bigger machine and use a longer chain. Don’t worry about this shed- the floor was rotten, so we were taking down as a favor. Honestly this shed didn’t even stand a chance- it was disappointing how fast it came down. Now I need something else to smash. I’ve always wanted to learn to play the piano- maybe another day. Sorry, that joke was off key. Smashing stuff with this wrecking ball was some of the most fun I’ve had in a long time, and it held up perfect. Let me know, what should I smash next? @hausplans #construction #demolition #heavyequipment #diy #hack
Not rated yetHow to Repair an Underground Water Line
· 1 min
One of my guys just hit an underground water line. Let’s see if we can fix it. First, I shut off the water. This pipe ran to a trailer that’s no longer on the property, but I still need to fix it because we’re using it for temporary water. I’m using ratcheting pipe cutters to cut this pipe below the damage. This will give me a nice clean cut. I want to reuse this ball valve, so I need to get the old pipe off. This is polyethylene pipe, and it’s used for underground water lines and wells. The pipe is attached to the fittings with hose clamps and fittings have barbs so to get it apart you heat the pipe. Here you can see the barbs. Alright, let’s get this put back together. I’m using two stainless steel clamps, with the screws turned opposite of each other. Next, I heat up the pipe with the torch and push the ball valve into place. Finally, I tighten both hose clamps and turn the water back on. No leaks. We’re about to build a brand-new shop right on this spot. So, if you want to follow along with this shop build, make sure to hit the subscribe button. @hausplans #build #howto #construction #diy #contractor
Not rated yet3 Easy Hacks for Working Construction Alone
· 1 min
One of my workers messed up big time today. He backed into the electric panel and broke a water line, so I had to send him home early. Now I’ve got a problem, I need to install this heavy sheet of PVC for the new electrical service by myself. So, I’m gonna show you a few hacks for working by yourself. Frist, if you need to take a long measurement or snap a line, drive a nail at the point you want to measure from and hook your tape or chalk line on it. Next, use a temporary ledger board. I’m screwing this 2 x 4 underneath the panel I need to install. It acts as a ledge to hold the piece in the exact position I need. Because the 2 x 4 is perfectly level and at the right height, I don’t need to measure- I just nail it in place. I find where the studs are in the wall and mark their locations onto the PVC. I start my screws ahead time and have my impact driver where I can grab it fast. Normally I couldn't do this job by myself, but with these tricks this hard job just got easy.@hausplans #build #howto #construction #contractor #hack
Not rated yetI Tried to Build a 1,000 lb Wrecking Ball in My Garage
· 1 min
I’m building a 1,000-pound wrecking ball in my garage. It’s going to be made out of concrete and I’m using an ocean buoy for the form. I built a crate around the buoy to support it; then I cut the top off so we could fill it with concrete. Here’s the problem, I need a way to attach a chain to my wrecking ball. I’m going to use a draw bar for a tractor and a shackle. But first I need to cut off the end of the draw bar so the shackle can swing freely. I’m planning to insert this draw bar into the concrete while it’s wet. So, I cut up some grade pins and tack them to the draw bar- this way it won’t pull out of the concrete. Next, I mix up concrete with a special ingredient- reinforcing fiber. This wrecking ball is going to take a beating, and the fiber will keep it from cracking apart. I used 13 bags of concrete- so it weighs closer to 700 pounds, but it will definitely get the job done! I put in some steel grade pins for reinforcement and finally the draw bar. I can’t wait to use this! Let me know what would you like to see me demolish? @hausplans #build #howto #construction #diy #contractor
Not rated yetWe Built Custom Stairs - And Had Everything Delivered from @HomeDepot #homedepotpartner
· 11 min
Building stairs is hard, but there’s no need to fear the stair monster! We teamed up with The Home Depot @HomeDepot #homedepotpartner, and I’m going to show you how to build a strong, custom set of stairs, step by step. And here’s the crazy thing: we scheduled an inspection for the end, so stick around to see if we pass or fail! First, I measure from the finished basement floor to the finished first floor. The total height is 121 inches. Dividing that by 16 gives me a riser height of approximately 7 9/16 inches. Always check your local building codes before building stairs because requirements can vary. Next, I build the landing, calculating its height so it lines up perfectly with the stairs. One side is supported by a wall, and the other by joist hangers and a beam pocket. I double up the end joists for extra strength, build the supporting wall, and install the remaining joists. The number one enemy of stairs is squeaks, so I use LedgerLOK structural screws to secure the landing to the wall studs and minimize movement. Then I apply floor adhesive, install the 3/4-inch subfloor, and fasten it with construction screws. I ordered everything for this project through The Home Depot, including lumber, hangers, fasteners, specialty tools, and adhesive. Since this job is in the middle of nowhere, delivery saved me a ton of time driving back and forth to the store. Now let’s cut some stringers! I’m using straight 2x12s with as few knots as possible. The rise is 7 9/16 inches, and the run is 9 1/2 inches. I lay out the steps using a framing square and stair gauges. These little tools keep the measurements consistent and make the process much faster. I carefully cut the first stringer, making sure not to cut past the lines because that can weaken the board. Since the treads are an inch thick, I also adjust the bottom riser to account for that thickness. Before cutting the rest, I test-fit the first stringer and check that everything sits properly against the floor and landing. I even use sample flooring and a tread to verify the finished step height. Once everything checks out, I use that first stringer as a pattern for the others. This is much more accurate than measuring every stringer individually. I’m installing four stringers, spaced about 11 inches on center, to make the stairs strong and prevent bouncing. I also attach 2x4 spacers to the outside stringers to leave room for drywall and skirtboards. Is it just me, or does this look like a giant dinosaur mouth? At the top, I use Simpson stringer connectors to secure the stringers to the landing. At the bottom, I install a pressure-treated 2x4 plate against the concrete. I notch the stringers so they fit securely against it and fasten everything in place. Since the stringers aren’t pressure-treated, I add sill seal to their bottoms to help protect them from moisture. I install the outside stringers first, then the middle ones, checking everything with a level before fastening them. A piece of scrap LVL underneath helps pull all four stringers into alignment. I also use structural screws to secure the outside stringers to the wall studs, making the staircase stronger and reducing movement that could cause squeaks. Then I repeat the process for the shorter set of stairs leading from the landing to the first floor. Because the landing flooring and stair treads have different thicknesses, I make a small adjustment to the bottom of those stringers to ensure the finished step heights match. For now, I install scrap subfloor as temporary treads. Once the drywall is finished, we’ll add oak treads and painted risers. These stairs are looking like a work of art! And wouldn’t you know it? Just as I finished, the inspector pulled up. I’ve had this guy before, and he’s super picky. He checked every screw and made notes on his tiny clipboard. Luckily, we passed! Building stairs takes careful measurements, solid connections, and attention to local building codes.…
Not rated yetWhat Keeps a Hurricane From Sucking The Roof Off a House?
· 1 min
Could this orange screw keep a hurricane from sucking the roof off your house? The roof trusses in most houses are held down with nails. Once the truss is set in place, it’s toenailed to the top of the wall- two nails on one side and a third nail on the other side centered between the two. But check this out… With this 6” truss screw I’m gonna screw from the bottom of the double plate all the way up into the truss chord. Just one of these screws gives up to 600 pounds of uplift resistance depending on the lumber. The screws are painted orange so they’re easy for an inspector to see. You could use hurricane ties, but they require driving in ten nails. So, what if there is a stud or header right below the truss? In that situation, you screw through the front of double plate at an angle. These screws come with a metal guide to help you set the screw at the right angle- 22 ½ degrees up into the truss. Technically code only requires an uplift connector on trusses that have more than 200 pounds of uplift, but for about a dollar a piece I’m putting one on every truss. Let me know, would you truss these? @hausplans #build #howto #construction #diy #contractor
Not rated yetHow to Install Silt Fence (We Failed Inspection)
· 1 min
We just failed inspection- let me explain. We’re building a new home for a customer and they’re adding a shop at the back of the property. Before I start excavation, I’m required to install silt fence and this gets inspected. First, I had to trench a ditch – unfortunately I kept hitting rocks, one right after another. This made the ditch crooked. Thankfully, I had my son helping me. I did the hard work driving the tractor and gave him the easy job of picking up these small rocks. Silt fence always gets installed on the downhill side of your worksite. It’s made from a woven plastic that traps the silt but lets the water seep through. The stakes go on the down hill side, and I like to roll up the ends so they’re less likely to tear. Once it’s installed you backfill up to red line. Over time the ends of the silt fence can start to pull in so I reinforce mine with an extra stake on a 45-degree angle. No sooner than we were done than I heard the inspector pull up. This guy is known for being super picky. Unfortunately, he said my ditch was crooked and I needed to tear the whole thing out and start over. @hausplans #build #howto #construction #diy #contractor
Not rated yetMaking Apple Cider With A Wood Chipper #sponsored @5hourenergyshot
· 1 min
We just attempted to make apple cider using only construction tools. And we used 5 hour Energy’s Caramel Apple shots to enhance the flavor. #sponsored @5hourenergyshot #5hourambassador I rented an industrial a wood chipper and dumped the apples in with an excavator. I had no idea if this would even work wood chippers are designed to chip trees, not apples. At first the chipper kept clogging up, but eventually a ton of apple shot through. Next, I had one of my friends weld up a giant smasher attachment that I bolted to my skid steer. I used the weight of the machine to push all the juice out of the apples. Go big or go home- it definitely did the job! Now, I’m gonna show you how to make one of the best drinks I’ve ever had. First, add vanilla ice cream and apple cider. Mine had a little bit of pulp in it. Then you dump in a 5 hour Energy Caramel Apple shot for a refreshing caramel apple twist. Next, we added whipped cream and drizzled caramel on top with a caulk gun. Finally, I used a piece of 1” PEX pipe for a straw. This drink was delicious! I just hope the rental shop doesn’t ask why the chipper smells like apples. @hausplans #construction #heavyequipment #cooking
Not rated yetHere’s a Hack for Building Stairs - Let’s get it done with @HomeDepot Delivery #homedepotpartner
· 1 min
Building stairs can be frustrating, so we teamed up with The Home Depot for this project- Let’s get it done! @HomeDepot #homedepotpartner #THDPro First, I put down a piece of sample flooring, then I measure from the floor to the top of the landing- 75 ¾ That gives me ten risers at 7 9/16ths and a run of 9 ½. This job is in the middle of nowhere, so I saved time and money by having The Home Depot deliver everything I need - lumber, fasteners and the tools. To lay off the stringer I put one side of the square at 9 ½ and the other at 7 9/16ths; then I mark it out. But I know what you’re thinking- there’s gotta be a faster way. There is! Check out these stair gauges I bought. I just clamp them down and they hold the square exactly where it needs to be. Next, I use are circular saw to cut out the stringer being careful not to go past my mark. Now it’s really tempting to want to karate chop these pieces off, but a reciprocating saw does a much cleaner job. I’m always nervous to see how the first one is going to fit- not bad at all! @hausplans #construction #howto
Not rated yetAre You Chaining Down Your Equipment Wrong?
· 1 min
This is gonna be controversial. Here’s the right way to chain down a piece of equipment. This Cat weighs about 10,500 pounds. Anything over 10,000 needs a separate tiedown on all four corners: two pulling forward, two pulling back. The rule is your tiedowns have to add up to at least half the machine's weight. Half of 10,500 is 5,250. Each tiedown is only as strong as its weakest part. My D-rings are rated 6,130, my chain and hooks are over 6,600, and my binders are 12,000. The D-rings are the lowest, so each tiedown counts as 6,130. But here's the part most people miss. When a chain runs straight from the trailer to the machine, you only get to count half its rating. Half of 6,130 is 3,065. Times four is 12,260, more than double what the law requires. Last, the forks have to sit flat on the deck. I throw a ratchet strap over them so nothing moves, and keep it off sharp edges. There's only one thing left to say. That's not going anywhere!@hausplans #construction #heavyequipment #trailer #howto #contractor
Not rated yetFrying a $169 Ostrich Egg in a Skid Steer Bucket
· 59 sec
We just made breakfast on the jobsite with ostrich eggs, and they’re huge- just look at one next to an average size construction worker. They’re not easy to open either – I used a Sawzall with a special metal cutting blade. Just one of these jumbo-sized ostrich eggs is equal to 30 chicken eggs. I wanted to scramble this egg, so I used my drill with an 1 ½” spade bit to beat the egg. To fry the egg we heated up the skid steer bucket with a torch. I put down a shovel full of butter so the egg wouldn’t stick. It’s crazy that all of that came from just one egg. I had this egg flown in from New Mexico and it cost me $169.00. I wanted to keep this simple- salt, black pepper, and some of my homemade Fuego powder- this stuff really is deadly. Finally, I added some sharp cheddar cheese. Once all the cheese melted, I garnished the egg with parsley. I’ve never had ostrich egg before, but it tastes a lot like a chicken egg. I’m on a diet, so I was proud of myself for only eating one egg. The New Guys sucked his up like he was a vacuum cleaner. @hausplans #construction #heavyequipment #cooking #contractor #chef
Not rated yetHow to Fix an Uneven Subfloor
· 1 min
Imagine paying a million dollars for a new home and the floors are uneven. This happens a lot, especially in bonus rooms above a garage- because the floor system is actually in the roof trusses. Here we have four trusses that are bolted together, and because each one is slightly different it’s causing unevenness in the floor. To fix it- I start by finding all the nails and circling them. Then I use a punch and a 2-pound sledge to sink them down. Next, I go at it with an electric planer. I start at the high point and lift it up as I move across the floor. Here’s a nail I missed- hitting a nail will with a planer can destroy the blade. Now I know what you’re thinking- doesn’t this weaken the floor? Actually, because I’m mainly planing above a truss and only removing a small amount- it’s not gonna hurt it. Finally, I load 50 grit sandpaper onto my belt sander and use it to blend the two floors together. That great thing about this belt sander is I can get right up against the wall where the planer couldn’t reach. Luckily, this was the only spot in the house that I had to repair; and once the floor was done it was smooth as butter. Now I just need someone to clean up this mess. @hausplans #build #howto #construction #diy #contractor #tools
Not rated yetDid Bobcat Just Make a Tank? #sponsored @BobcatCo
· 1 min
Did Bobcat just make a tank? #sponsored @BobcatCo #bobcatpartner #onetoughanimal Check out the metal guards and polycarbonate glass. Actually this is a new Bobcat PRO loader and they invited me to Texas to try it out. This T86-2 has the land management package on it. With 115 horsepower it chewed through this log like it was a #2 pencil. So, what are the PRO features? Let’s start with one of my favorites- “Bobcat Sense”. Look how easily I just backed over these cones- what if it had been my truck? With “Bobcat Sense” you get rear object detection. Here I’ve got the throttle wide open, and it won’t let the machine back into the cones. The Pro loaders come with a touch screen display and 4 drive modes. But what if you want a familiar machine without the technology? Bobcat has a full line of Classic loaders. This T650 was fun to operate. It’s the perfect size and was super agile. Let me know in the comments, would you go with a PRO loader or would you rather have a Classic loader? @hausplans #construction #heavyequipment
Not rated yetMake Sure Your Deck Never Collapses
· 1 min
How can you support the weight of a deck, so it doesn’t collapse? These posts transfer the weight of the deck above down onto the patio, and under the posts we poured two 24” deep concrete piers. I need to tie the concrete patio under the deck into the piers. I start by drilling four 5/8ths inch holes 6 inches deep. Next, I blow out the holes with compressed air and scrub them out with a brush. Finally, I blow them out one last time- I don’t want any dust. I measure from the top of the pier up to the rebar grid in the patio. Then I bend eight pieces of ½” rebar into an “L” shape. I’m going to anchor the steel rebar into the concrete with a two-part epoxy. We dug these piers and had them inspected when we did the rest of the footings for the house. The bottom of these footings will be more than 30” deep, which is lower than the ground freezes in our area, so this slab should never heave from frost. Now I tie the “L” pieces into the rest of the rebar grid. Once we’re done, this deck will be strong enough to park a truck on. @hausplans #build #howto #construction #diy #contractor #deck #patio
Not rated yet