Skip to main content
AmigoFish

Dune Buggy Warehouse

Dune Buggy WarehouseVideoLast show:

Not rated yet

No new videos since January 2026.

About this show

www.dunebuggywarehouse.com Beetle & Buggy Parts. Air Cooled since 1986. We breathe street, strip, performance, and off road. Located in Hamilton, Ohio.

Videos come from the channel's public YouTube feed. The artwork is the newest video thumbnail. Last updated . Names, artwork and text belong to their publishers.

Cosmos

Similar by topic and creator

  • The Drive
    Shares the topic Cars and Motoring.
  • Ideal
    Shares the topic Cars and Motoring.
  • VINwiki
    Shares the topic Cars and Motoring.

See the full Cosmos

Videos

  • How To Measure Deck Height with Basic Tools - Air Cooled VW Tech Tips

    · 59 sec

    Here is one way to measure your deck height with basic tools on an Aircooled VW engine. For this video we used a set of dial calipers, deck height tool part number 5756, and a marker. This measurement way is suitable for a reasonable compression ratio street engine. After removing the cylinder head, keep any shims for the final measurements. Install the deck height tool, screw in the set screw, and rotate the crank to touch the piston to set screw. Mark this position on the flywheel or pulley - we use the case half as the alignment. Rotate engine back the other way until you touch the piston to the set screw, and mark the flywheel or pulley again. Between these two marks is TDC - Top Dead Center. Back off the set screw and rotate to TDC, then measure your depth with the dial calipers. Measurement should be on either end of the wrist pin to minimize the piston rocking. Take this depth measurement (Ours was 0.576” depth), subtract the thickness of your deck height plate (ours was 0.450”), add the thickness of any head shims (one 0.060” shim on this engine) and you have your deck height total. We do recommend measuring cylinders on both sides of the engine to help verify your crankcase centerline. Our engine measurements as example: Our depth was 0.576” Our deck height plate thickness 0.450” One cylinder head shim 0.060” 0.576” depth -.450” plate thickness +.060” head shim =.176” deck height Use your deck height measurement in an engine calculator, along with cylinder head CC, to help calculate compression ratio. If you are looking for VW Type 1 Engine replacement and performance parts for your VW Air-cooled Beetle, Bug, Dune Buggy, Sand Rail, Woods Buggy or even your Thing & Ghia, check out our website: https://www.DuneBuggyWarehouse.com Follow us on Social Media! Facebook: https://www.facebook.com/dunebuggywarehouse Instagram: https://www.instagram.com/dunebuggywarehouse

    Not rated yet
  • How To Install Window Seals in your Beetle - DuneBuggyWarehouse

    · 57 sec

    Here are some tips on how to install windows into your VW Beetle. For this project we installed Empi Cal-Look window seals (Empi part 00-3587-0) into Rick's 1965 Drag Beetle project. We start with the rear window and side windows. Nylon rope, and plenty of dish soap mixed with water are your tools. Bug windshields are the most fragile part of this project so we usually install that last. Firm but gentle pressure while pulling the rope around is key to getting the window seal to grab the body lip. This video features a Cal-Look window rubber kit. If your bug has stock window trim, you'll need to install the trim moldings before installing the windows in the car. Questions or comments, leave them below or email us: sales@dunebuggywarehouse.com If you are looking for VW Type 1 Engine replacement and performance parts for your VW Air-cooled Beetle, Bug, Dune Buggy, Sand Rail, Woods Buggy or even your Thing & Ghia, check out our website: https://www.DuneBuggyWarehouse.com Follow us on Social Media! Facebook: https://www.facebook.com/dunebuggywarehouse Instagram: https://www.instagram.com/dunebuggywarehouse

    Not rated yet
  • Pressure Plate and Throw Out Bearings - Air Cooled VW Tech Tips

    · 1 min

    Here's a quick tech tip on Air Cooled VW pressure plates and throw out bearings (or clutch release bearings). There are two styles in the Air Cooled VW world. Early style (1970 & earlier) clutch & throw out bearing has a collar on the pressure plate fingers, removable clips, and does not have any guide sleeve. Late style (1971 & later) clutch & throw out bearing has a guide sleeve, clips are molded into the throw out bearing, and no collar on the pressure plate fingers. Check out our Clutch & Flywheel parts for your Air-Cooled VW or Buggy here: https://dunebuggywarehouse.com/collections/clutch-flywheel If you have any questions or comments, leave them below or email us: Sales@DuneBuggyWarehouse.com Swing Axle vs IRS Transmissions - How to tell the difference: https://www.youtube.com/watch?v=Ip8EXS1mkEw If you are looking for VW Type 1 Engine replacement and performance parts for your VW Air-cooled Beetle, Bug, Dune Buggy, Sand Rail, Woods Buggy or even your Thing & Ghia, check out our website: https://www.DuneBuggyWarehouse.com Follow us on Social Media! Facebook: https://www.facebook.com/dunebuggywarehouse Instagram: https://www.instagram.com/dunebuggywarehouse

    Not rated yet
  • How to Assemble an Empi Carb Sync - DuneBuggyWarehouse

    · 1 min

    A quick tutorial on how to assemble an Empi Carburetor Synchronizer from DuneBuggyWarehouse. This works for Empi part number 43-5712-0 or 43-5718-0 and should work for other similar brands of carb syncs. Thanks for watching! https://dunebuggywarehouse.com/ @DuneBuggyWarehouse Learn how to inspect a VW Type 1 Engine Case here: https://www.youtube.com/watch?v=vCmFre0ckKE

    Not rated yet
  • TDI Starter Adapter for Type 1 Sedan and 002 Bus Transaxles - DuneBuggyWarehouse

    · 2 min

    Our Dune Buggy Warehouse TDI Starter Adapter for Type 1 Sedan and 002 VW Bus Transaxles allows use of a much higher torque TDI Jetta starter in your dune buggy, sand rail, or beetle transaxle. These starters can easily handle high compression VW Type 1 or Type 4 engines, as well as Ecotech and Subaru swaps. For more information regarding the adapter plate in this video please visit: https://dunebuggywarehouse.com/vw-tdi-starter-and-adapter-plate-for-vw-beetle-sedan-transmission-3-rib-and-5-rib.html Thanks for watching! https://dunebuggywarehouse.com/ @DuneBuggyWarehouse Learn the difference between a Type 1 Beetle and Type 2 Bus Transmission: https://goo.gl/QwzSVH Learn the difference between Swing Axle and IRS: https://goo.gl/eoDMU5

    Not rated yet
  • TDI Starter Adapter for 091 and 094 6 Rib Bus Transaxles - DuneBuggyWarehouse

    · 2 min

    Our Dune Buggy Warehouse TDI Starter Adapter for 091 and 094 6-Rib VW Bus Transaxles allows use of a much higher torque TDI Jetta starter in your dune buggy, sand rail, or beetle transaxle. These starters can easily handle high compression VW Type 1 or Type 4 engines, as well as Ecotech and Subaru swaps. *Fitment note* These adapters do not fit in a split window or bay window VW Bus without additional clearance around the starter main power terminal. For more information regarding the adapter plate in this video please visit: https://dunebuggywarehouse.com/vw-tdi-starter-and-adapter-plate-for-vw-bus-6-rib-transmissions.html Thanks for watching! https://dunebuggywarehouse.com/ @dunebuggywarehouse Learn the difference between a Type 1 Beetle and Type 2 Bus Transmission: https://goo.gl/QwzSVH Learn the difference between Swing Axle and IRS: https://goo.gl/eoDMU5

    Not rated yet
  • How To Assemble a CV Joint - Air Cooled VW Tech Tips

    · 47 sec

    Here's a quick tech tip on how to assemble or reassemble a CV Joint. This is an Rzeppa style constant velocity joint with balls and a cage. These are a very common style of CV joint used in cars, trucks, and off-road vehicles. Check out our CV Joints for your Air-Cooled VW or Buggy here: https://dunebuggywarehouse.com/collections/cv-joints If you have any questions or comments, leave them below or email us: Sales@DuneBuggyWarehouse.com How To Inspect Your VW Type 1 Engine Case: https://www.youtube.com/watch?v=vCmFre0ckKE If you are looking for VW Type 1 Engine replacement and performance parts for your VW Air-cooled Beetle, Bug, Dune Buggy, Sand Rail, Woods Buggy or even your Thing & Ghia, check out our website: https://www.DuneBuggyWarehouse.com Follow us on Social Media! Facebook: https://www.facebook.com/dunebuggywarehouse Instagram: https://www.instagram.com/dunebuggywarehouse

    Not rated yet
  • How To Measure a VW Type 1 Engine Case for Main Bearings - Air Cooled VW Tech Tips

    · 1 min

    Here's a quick tech tip showing you how to measure your VW Type 1 engine case for main bearings. See ALL the engine bearing measurements in our Main Bearing Size Chart here: https://dunebuggywarehouse.com/blogs/news/vw-type-1-main-bearing-sizing-chart-for-vw-beetle-dune-buggy-engines This is a 'quick and dirty' method showing where you need to measure. A bore gauge on a torqued engine case will always be the most reliable way to measure, but this video will help if all you have are dial calipers. VW's wear limit on case bore is +0.001" but as a general rule, your bearings should snap into place and fit snugly with the case halves torqued. If your bearing fits loose it may be time for an align bore. If you have any questions or comments, leave them below or email us: Sales@DuneBuggyWarehouse.com How To Inspect Your VW Type 1 Engine Case: https://www.youtube.com/watch?v=vCmFre0ckKE If you are looking for VW Type 1 Engine replacement and performance parts for your VW Air-cooled Beetle, Bug, Dune Buggy, Sand Rail, Woods Buggy or even your Thing & Ghia, check out our website: https://www.DuneBuggyWarehouse.com Follow us on Social Media! Facebook: https://www.facebook.com/dunebuggywarehouse Instagram: https://www.instagram.com/dunebuggywarehouse

    Not rated yet
  • 1968cc VW Type 1 Dyno Test - 92mm bore x 74mm stroke - 38 Egas carburetor

    · 1 min

    Trying out an interesting combination for a reliable, streetable 1968cc VW Type 1 engine. Pairing 92mm thickwall pistons to a 74mm stroker crankshaft, an FK7 camp with 1.25 ratio rockers in a pair of EMPI's GTV2 heads running 40mm x 35mm valves. With the intent being a reliable but punchy street engine, we kept an 8:1 compression ratio, running a 38 Egas carburetor. This 1968cc combination made 110 ft-lbs of torque at 2600 rpm, yielding a broad torque curve with just shy of 80 horsepower at 4600rpm. Overall this engine combination shows excellent punchy street manners. If you have questions on engine sizes or components, leave it below or send us an email at: Sales@Dunebuggywarehouse.com Check out our website specializing in parts for air-cooled Beetles and dune buggies: https://dunebuggywarehouse.com/ For VW Type 1 engine parts, click here: https://dunebuggywarehouse.com/engine.html?cat=243 Thanks for watching!

    Not rated yet
  • Air Cooled Street Car Association Qualifying at VW Drag Night 2018

    · 7 min

    With big horse power in a VW powered street car the Air-Cooled Street Car Association Cars were one of the most popular classes of racers at VW Drag Night. ASA cars must drive a 30 mile loop prior to racing. This class is all inclusive and features power adder cars or naturally aspirated cars. This was one round of qualifying during VW Drag Night 2018

    Not rated yet
  • Dune Buggy Warehouse Nationals Final Race Pat Downs vs Ollie Frey VW Drag Night 2018

    · 2 min

    Final battle for $5000 in the Dune Buggy Warehouse Nationals VW Pro Stock Race at VW Drag Night 2018. Ollie Frey versus Pat Downs.

    Not rated yet
  • VW Pro Mod Race at VW Drag Night 2018 Austin Johnson vs Red Baron

    · 21 sec

    Austin Johnson cuts a 6.09 pass in his turbo VW Bug against the Red Baron at VW Drag Night 2018 sponsored by Dune Buggy Warehouse. This was in qualifying for the Pro Mod class featuring power adder cars. The race was held at the South Carolina Motorplex

    Not rated yet
  • Pat Downs vs Alex Curry at Dune Buggy Warehouse Pro Stock Nationals VW Drag Night 2018

    · 25 sec

    Pro Stock run between Pat Downs of CB Performance and Alex Curry of Curry Racing at the Dune Buggy Warehouse Pro Stock Nationals. The race was held at South Carolina Motorplex near Orangeburg South Carolina. This was shot at Drag Nights 2018. Pat Downs won the event with consistent sub six second eighth mile passes. Curry fought gremlins in his car all day.

    Not rated yet
  • Vintage VW Dirt Track Race Car Seen at VW Drag Night 2018

    · 36 sec

    Check out this vintage dirt track VW bug. It is fully caged and prepared for wheel to wheel dirt racing! Notice the offset pedals and shifter. This thing is ready to go sideways!

    Not rated yet
  • Pro Mod VW Race Cars Line Up at VW Drag Night 2018

    · 18 sec

    Here are several of the VW Pro Mod racecars lined up for some runs down the drag strip at VW Drag Night. The event was hosted at South Carolina Motorplex in Orangeburg, Sc. Many of these cars use turbocharged or nitrous powered VW Type 1 engines.

    Not rated yet
  • Air-Cooled Street Car Association Race Cars Line up at VW Drag Night 2018

    · 33 sec

    Here are several of the Air-Cooled Street Car Association cars lined up for some runs down the drag strip at VW Drag Night. The event was hosted at South Carolina Motorplex in Orangeburg, Sc. Many of these cars use turbocharged or naturally aspirated VW Type 1 engines.

    Not rated yet
  • How To Inspect Your VW Type 1 Engine Case - Air-Cooled VW Tech Tips - The Oil Leak EP2

    · 12 min

    If you're looking to re-use your VW Type 1 Engine Case, build a monster race motor with a donor block, or you're hunting for a used engine or engine block at the next BugSwap event, here is one of the most thorough tutorials on how to inspect a VW Type 1 engine case. You can read this article on our website: https://dunebuggywarehouse.com/https/how-to-inspect-your-vw-type-1-engine-case.html Thanks for watching! If you have questions or comments, leave them below or email us: Sales@DuneBuggyWarehouse.com More Tutorials: Flat vs Dished Cam - Which Oil Pump Do I need? https://www.youtube.com/watch?v=JsVX8OqIgVM King Pin vs Ball Joint Front Suspension - How to tell the difference: https://www.youtube.com/watch?v=VocRlfxDXPg If you are looking for VW Type 1 Engine replacement and performance parts for your VW Air-cooled Beetle, Bug, Dune Buggy, Sand Rail, Woods Buggy or even your Thing & Ghia, check out our website: https://www.DuneBuggyWarehouse.com Follow us on Social Media! Facebook: https://www.facebook.com/dunebuggywarehouse Instagram: https://www.instagram.com/dunebuggywarehouse

    Not rated yet
  • How to Identify a Late Model Beetle - The Oil Leak - Episode 1

    · 4 min

    A 1970 VW Beetle made it's way into our back lot. Here are some tips on how to visually identify a late-model beetle and how to check for a locked up engine. What should we do with this rad rotted car? Check out some of our other Air-Cooled Tech Tips: What style oil pump do I need? Flat Cam vs. Dished Cam: https://www.youtube.com/watch?v=JsVX8OqIgVM King Pin vs. Ball Joint - How to tell the difference: https://www.youtube.com/watch?v=VocRlfxDXPg Dune Buggy Warehouse is your premier retailer for Air-Cooled VW parts and performance accessories. Looking to restore your Type 1 Beetle, or build the baddest air-cooled buggy? Check us out at: https://dunebuggywarehouse.com/

    Not rated yet
  • Fitech's Prototype 2 Barrel Fuel injection unit From SEMA 2017

    · 4 min

    A quick look at the new 2-Barrel prototype for FiTech Fuel Injection kits. Interested in great parts at better prices? Check out our Air-cooled VW parts selection and get your Air-cooled Beetle, Dune Buggy, Sand Rail and Woods Buggy outfitted and ready for cruising, bashing or blasting! https://dunebuggywarehouse.com/ This was a Live video from Sema Show 2017, downloaded from our Facebook page and re-uploaded for Youtube.

    Not rated yet
  • Baja 1000 Prep with Drews Racing - Facebook Livestream 11/7/2017

    · 1 hr 46 min

    We had a livestream session with Drews Racing preparing their Vintage Aircooled class Buggy for the Baja 1000 in a few days, including a first-start of the 2276cc VW engine with Fitech fuel injection. This included troubleshooting oil pressure, a semi no-start condition with the Fitech, ending with a bit of a blowout! In the end, the 2276 started and ran great during the cam break-in, and blew an oil line off the oil filter. No hose clamps were harmed in the making of this video (but they were tightened afterwards!). Phillip and crew are heading to Encinada, Mexico in just a couple days and will be participating in the 2017 Baja 1000. Many of the parts on this buggy are sourced from Dune Buggy Warehouse. Video downloaded from our Facebook Livestream session on 11/7/2017.

    Not rated yet