Skip to main content
AmigoFish

Understanding Infusion Mashing: A Comprehensive Guide for Homebrewers

From BeerSmith Home Brewing ·

Playback is not available here.

Open it at the source

Not rated yet

Description

https://d3pddo38v7j30h.cloudfront.net/blog/wp-content/uploads/2016/12/P1170273.jpg This week I take a look at infusion mashing, an method for managing your mash step temperatures during the mash phase of an all-grain brewing session.

Mashing for All Grain Brewers

The majority of home and professional brewers use an all-grain method for brewing where they start with malted barley grains, and go through phases for the mashing, sparging, boiling, cooling and fermenting the wort into beer. During the mash phase, the crushed malted grains are mixed with water and heated up to a target temperature typically between 146-158F (63-70 C) where enzymes natural to the grain act to break longer starch chains into simple sugars (https://beersmith.com/blog/2021/10/02/enzymes-in-beer-alpha-and-beta-amylase/) like maltose that can easily be fermented by yeast later in the process. Depending on how modified the malt is (https://beersmith.com/blog/2010/01/04/diastatic-power-and-mashing-your-beer/) and the conditions in the mash this process can take anywhere from 20 minutes to over an hour.

Some brewers have historically used a multi-step mash with a timed rest at different temperatures to achieve additional effects. For example the Lager (German) mash profile is widely used with many European lager styles (https://beersmith.com/blog/2023/07/18/the-german-step-mash-profile-for-beer-brewing/). It uses a two step mash with the first step in the mid-140’s F (63 C) and the second step in the 159 F (70 C) temperature range. Hitting both steps results in a beer that achieves high fermentability due to the enzymes activated, but still retains good mouthfeel. There are a variety of other multi-step profiles historically used with undermodified malts, but these have largely fallen out of favor with modern brewers who prefer the simplicity and time savings of a single-step mash, occasionally varying into a two step German/Lager mash described above for certain styles.

The Infusion Mashing Method

For the initial infusion mash step, most brewers will target a given water/grain ratio to determine the volume of water to use in the mash. For conventional mashing this water/grain ratio is typically in the 1.25-2 quarts/lb range. For brew-in-a-bag and all-in-one systems often the total water needed for the batch is included up front, resulting in much higher water/grain ratios. Some traditional decoction mash profiles also use high water/grain ratios in the 3-4 qt/lb range.

For a given amount of mash water and grains, it is fairly easy to find the equation for infusion estimates which is based on the specific heat of water, specific heat of grains and the relative volumes and temperature differential. However in practice most brewer use an online calculator or software such as BeerSmith (https://beersmith.com)to get the temperature and then just heat their water to that target temperature before mashing in. Once you have the temperature you just heat your water up to that value and then mix in the malts.

Mashing Methods – Achieving Your Target Temperature

Once you have established whether you want to use a single-step or multi-step mash the next decision to make is how to achieve the target temperature for each step. There are three general methods we can apply:

- Infusion Mashing – Water is heated either in the main vessel or a secondary hot liquor tun to a target temperature. For the first step, we usually add the water first and then “dough-in” the grains to achieve the target temperature. In later steps, more hot water can be added to raise the overall temperature, or you can use direct heating or a decoction step.

- Direct Heating – Some mash tuns can be directly heated. We can apply heat to the water before mashing in to do an initial infusion step as described above, and then apply more heat if we need to raise the temperature for subsequent steps. This is often called a “temperature step” as we change the temperature without adding more water.…

Back to BeerSmith Home Brewing · Report a problem