New Mash pH Adjustment Tools for Beer Brewing in BeerSmith 4
From BeerSmith Home Brewing ·
Playback is not available here.
Description
Today I present a quick overview of the new mash pH adjustment tools in BeerSmith 4 which is available now at BeerSmith.com (https://beersmith.com).
The Importance of Mash pH Adjustment for All-Grain Brewing
For many years now, brewers have known that mash pH adjustment is important for all grain brewers. Getting the right mash pH (https://beersmith.com/blog/2016/02/23/residual-alkalinity-and-ph-for-all-grain-beer-brewing/) can enhance the extraction of sugars, wort viscosity, hop utilization, color and tanin extraction, improve the flavor of the beer and even help with long term stability.
The basic chemistry is not hard to understand. Pure water has a pH of 7.0, though many tap water sources are slightly alkaline with a pH of around 8. As we add grains to the mash, the grains have some acidity and will lower the pH. Darker grains have more acidity and will lower it more than lightly colored grains. The net result is that the mash will settle to a pH between 5.2 and 7.0 depending on the acidity of the base water, acidity of the grains used and also the buffering capacity of the water which is typically measured using a number called Residual Alkalinity (https://beersmith.com/blog/2016/02/23/residual-alkalinity-and-ph-for-all-grain-beer-brewing/).
The ideal mash pH for brewing is generally in the 5.2-5.6 range. While many darker beers can reach that range without adjustment due to the higher acidity of dark grains, most lighter colored beers require the addition of some acid to lower the pH down to the desired range.
To lower the mash pH a variety of acids can be used. The most commonly used are lactic acid, phosphoric acid and acid malt. These are added in small quantities either at mash in or once the mash pH has settled to bring the mash acid to the desired range.
Adjusting Your Mash pH in BeerSmith 4
While the older BeerSmith 3 used a somewhat complex calculator system to determine the acid to add things have been substantially simplified in BeerSmith 4. BeerSmith 4 has two buttons on the Mash tab (show below) that you can use. The first one Adjust acid from Estimated pH lets you calculate how much acid to use based on the pH estimated in BeerSmith. This estimate is calculated based on the adjusted water profile you used, the grain bill for your recipe and also the acid you select.
https://d3pddo38v7j30h.cloudfront.net/blog/wp-content/uploads/2026/03/mash-ph-adjust.png The second button titled Adjust Acid from pH Measurement instead uses a manual pH measurement you enter. The idea here is that you use a pH meter early in the mash process to determine the actual pH and then it will calculate how much acid to add based on the measurement and your target pH.
Mash pH Adjustment Examples
If you have a pH meter you can use either tool depending on how you want to handle your mash pH. I personally recommend making an initial adjustment based on the estimated mash pH and then make a second adjustment if the measured mash pH varies substantially from the target. I have an entire article on the merits of this strategy here. (https://beersmith.com/blog/2017/10/18/when-and-how-to-measure-and-adjust-mash-ph-for-beer-brewing/)
I should also mention that adjusting your mash pH is the last thing you should do before brewing. If you use the new Run Checks button to check your recipe before brewing you will likely see a reminder to finalize your water profile and mash pH. The reason for this is that any changes to the recipe’s grain bill or water volumes can change your water and pH chemistry, so you should generally finalize your water profile first and then finalize your mash pH last right before brewing to make sure they are up to date.
https://d3pddo38v7j30h.cloudfront.net/blog/wp-content/uploads/2026/03/mashPHFromEst-1.png Here’s an example using the Adjust Acid from Estimated pH button. In this case the software estimates my pH as 5.7 based on my current water profiles and grain bill in the recipe. I’ve entered my target…