Skip to main content
AmigoFish

A Brewer’s Guide to Adjusting Hard Water for Better Beer

From BeerSmith Home Brewing ·

Playback is not available here.

Open it at the source

Not rated yet

Description

https://d3pddo38v7j30h.cloudfront.net/blog/wp-content/uploads/2026/11/GlassesOnBarWeb.jpg

This week I take a look at what to do if your water source is simply too high in mineral content and ways you can compensate to brew great beer.

My Struggle with Bad Water

Back in the 1990’s when I first started brewing all grain beers, I lived in the mountains outside of Albuquerque, New Mexico where unfortunately the water was very high in mineral content. It was so hard, that we had to use bottled water to make coffee. I ended up also purchasing bottled water to make beer as the water was simply not usable for brewing.

Understanding Your Existing Brewing Water

Our knowledge base for brewing has expanded significantly in the last 30 years, so now we know a lot more about what to do about hard water or water that simply has high ion content. I would recommend that you first get your water tested for the big six water ions (https://beersmith.com/blog/2021/08/06/the-big-six-water-ions-and-water-chemistry-in-beer-brewing/) using a reputable test kit or lab that provides a brewing water report. This will give you a definitive measure of just how good or bad your water is.

With your water report you should get a measure of each of the following water ions in parts per million (ppm) or mg/l which are approximately the same thing. Here’s a guide for what each of the ions does and also the range that is acceptable for brewing:

- Calcium (Ca) [50-100 ppm] – Acidifies the mash and drives down the mash pH which is generally a good thing in lighter color beers. It also aids in precipitating phosphates and improving the stability of the beer. Calcium also provides some structure to the beer and is used in that role as well.

- Bicarbonate (HCO3) [0-250 ppm] or Alkalinity [0-200 ppm] – Strongly alkaline so it will raise the mash pH which is undesirable in lighter color beers. High levels also will impede the cold break and emphasize bitterness in a harsh way. The main role for these ions is in mash pH balance, and too much alkalinity can be undesirable. You can convert from bicarbonate to alkalinity using this equation: alkalinity = bicarbonate * 50 / 61

- Sulfate (SO4) [50-250 ppm] – Suilfate enhances bitterness in beer and slightly lightens color. Its primarily role is as a counterbalance to chloride in determining the sulfate/chloride ratio (https://beersmith.com/blog/2016/02/11/the-sulfate-to-chloride-ratio-and-beer-bitterness/) which affects bitterness perception in the final beer.

- Chloride (Cl) [0-250 ppm] – Chloride will lower the bitterness perception and enhance the maltiness of the beer. Its major role, along with sulfate, is in determining the sulfate/chloride ratio (https://beersmith.com/blog/2016/02/11/the-sulfate-to-chloride-ratio-and-beer-bitterness/) which affects bitterness perception in the beer.

- Sodium (Na) [0-150 ppm] – Sodium provides enhances the sweetness and body in certain dark beers. However it is not a major player in mash pH so it is primarily used to provide some roundness in darker beers.

- Magnesium (Mg) [10-40 ppm] – Magnesium plays an important role in fermentation as it is needed by yeast, but grains in the mash do provide about 100ppm of magnesium. However, recent research indicates that calcium may actually block the yeast’s access to magnesium if it is very high. So it may be important to keep the total magnesium levels (water plus magnesium from the mash) above the calcium to enhance yeast health. Magnesium also plays a small role in mash pH, but is largely overshadowed by bicarbonate and sulfate.

When looking at the ranges above, you need to keep in mind that those are general guidelines and the actual water profile needed will vary by style. For example, 200ppm bicarbonate might be perfectly acceptable in a stout but would not work well in a light continental lager. BeerSmith software (https://beersmith.com) has a series of water profiles under Ingredients->Water by city and style which you can…

Back to BeerSmith Home Brewing · Report a problem