SimonFordman
SimonFordmanVideo
- Format:
- YouTube channel
- New videos:
- Every two weeks
- Typical length:
- about 1 hour 50 minutes
- Latest video:
About this show
Howdy. I like fixing stuff and making videos. I hope you enjoy.
Videos come from the channel's public YouTube feed. The artwork is the newest video thumbnail. Last updated . Names, artwork and text belong to their publishers.
Cosmos
Similar by topic and creator
- RezzyCarz
Shares the topics Cars and Motoring and How-To and DIY. - High Peak Autos
Shares the topics Cars and Motoring and How-To and DIY. - Drivewhisperer
Shares the topics Cars and Motoring and How-To and DIY.
Videos
1973 Station Wagon - Engine Build
· 2 hr 39 min
- Turn on subtitles or view the transcript at the bottom of the description if you'd like explanations on what I'm doing throughout the video - This is my 1973 Mercury Montego station wagon that I got running and driving in a previous video. The 351 Cleveland engine was severely seized and although I got it unstuck, the cylinders had already suffered a lot of damage from corrosion. The engine may run, but it sounds a couple cylinders short of a V8. Knowing that it'd need extensive machine work to be fixed properly, I picked up a cheap 351 Windsor as a replacement. I expected to have the engine in the car and running by the end of the video, but after digging further into it, I decided to give it an at-home rebuild first. Now, the engine, along with an AOD overdrive transmission, is ready to be installed into the Wagon in the next video. Chapters: 00:00 - Bad engine 04:40 - Cheap 351 Windsor, will it run? 00:29:55 - Engine teardown 00:54:29 - Honing, measuring, cleaning 01:08:06 - Crankshaft polishing, measuring 01:12:10 - Rods/Mains measuring 01:15:10 - Camshaft/bearings installation 01:19:57 - Crankshaft installation 01:21:41 - Piston rings 01:32:08 - Installing pistons 01:35:03 - Timing chain, cover, pump, pan 01:42:21 - Mercruiser (free boat) cylinder heads 01:59:20 - Water pump, intake manifold detailing 02:02:43 - Painting 02:06:46 - Intake manifold installation 02:08:45 - Fuel pump, harmonic balancer, core plugs, rear main, etc. 02:14:58 - Priming the oiling system 02:16:42 - Valve covers, finishing the engine 02:18:00 - AOD tranmission service 02:27:35 - Mating the engine/transmission 02:31:22 - Next time 02:32:08 - F250 stuff 02:36:29 - Cats
Not rated yet1975 Mercury Montego
· 1 hr 20 min
- Turn on subtitles or view the transcript at the bottom of the description if you'd like explanations on what I'm doing throughout the video - This is a 1975 Mercury Montego MX Brougham. I went to go look at it with the intention of using it as a parts car for my 1973 Mercury wagon, I was mainly interested in the drivetrain. That being so, I was under the impression that it had a 351 Windsor. When I got to the car, I saw that it had the lesser 351 Modified, an engine I was not interested in salvaging for the wagon. At that point, I didn't really have a use for the car, but I was an hour and half away from home with my trailer and cash in hand, so I bought it anyways. I figured it would be fun to get it driving and cleaned up, and I saw that it's definitely worth saving instead of parting out. Despite that, no one wants to buy it. If you do, let me know. Chapters: 00:00 - Getting it home 05:38 - First looks 09:47 - Seeing if it'll run 18:03 - Brakes 24:55 - Seeing if it moves 28:13 - Pressure washing 36:55 - Cleaning the interior 45:30 - Finishing touches 48:37 - Driving 52:45 - Work on the F150 mud truck 1:18:05 - Cats
Not rated yetMore Power
· 1 hr 44 min
- Turn on subtitles/CC's if you'd like explanations on what I'm doing throughout the video. - My 1983 F250 has the smallest optioned engine, the Ford 300. It's a great engine, but when towing with it, the routine is to just floor it and wait, then wait some more, then wait more until it eventually reaches a barely reasonable highway speed, then keep it floored to maintain that. I've heavily considered putting a 460 in its place, but I think I just like this engine too much. So, I decided to try and get some more power out of it by installing a 4 barrel Offenhauser intake and Holley carburetor, EFI exhaust manifolds, mildly porting the cylinder head, and installing higher ratio chevy rocker arms. I also put in heavier leaf springs (for towing), installed a larger winch, and did a few other things that I've been meaning to do for a while now. Chapters: 00:00 - 0-55 (won't hit 60) time 02:22 - Removing the cylinder head 08:28 - Disassembling the head 11:26 - Porting the cylinder head 14:22 - Lapping and installing the valves 21:45 - Aluminum intake and EFI exhaust manifolds 24:04 - Installing the cylinder head 26:43 - Chevrolet 1.75 ratio rocker arms 30:35 - Carburetor rebuild 37:55 - Carburetor install 41:23 - Exhaust 43:38 - First start 45:42 - Heavy duty leaf springs 56:34 - Warn M12000 winch installation 1:11:43 - Roll bar 1:16:40 - Fog lights 1:26:06 - Finishing touches 1:29:10 - Driving, 0-55 time test 1:32:24 - Getting stuck in the mud again 1:40:51 - Chevelle return 1:42:46 - Cats
Not rated yet1971 Chevelle (Burnt)
· 2 hr 10 min
- Turn on subtitles/CC's if you'd like explanations on what I'm doing throughout the video. - This is a 1971 Chevrolet Chevelle. It has a big block 454 and no rust holes to speak of. However, it was in a fire. Most everything not-metal had been melted away and then the burning structure proceeded to fall down on top of the car, covering it in debris. Compounding that, the car was then left outside with no hood or air cleaner over the engine for what I assume to be more than just a few years, leaving it to corrosion and critter infestation. Nonetheless, all the important parts are still there, so surely this one is ready to drive again with just a little work. Chapters: 00:00 - Getting it home 08:33 - Removing melted wiring and cleaning up the engine 17:19 - Un-seizing the engine 21:53 - Connecting power/fixing the starter. 26:32 - Carburetor(s) 31:45 - Getting spark 34:35 - Stuck shifter 36:42 - Prep for first start 38:04 - First start 39:23 - Testing the transmission/brakes 42:16 - Clean - up 56:59 - Fuel system 01:01:02 - Cooling system 01:02:59 - Oil change/Severely stuck oil filter 01:07:54 - Shifter fix/seat fitment/gas pedal 01:17:55 - Running the engine up to temp/tune-up/checks 01:21:33 - New wheels/tires 01:26:06 - Re-wiring the engine 01:36:25 - Flex-plate is in backwards 01:45:42 - Re-wiring the lights 01:55:36 - Finishing touches 02:00:55 - First Drive 02:07:19 - Cats
Not rated yet4x4 Roadtrip to the Dunes.
· 1 hr 40 min
- Turn on subtitles/CC's if you'd like explanations on what I'm doing throughout the video. - I thought it was about time for an adventure, so I decided to take my rusty 4x4 Ford pickup that I never intended to drive on interstates again on a 1000 mile round trip to the Silver Lake sand dunes in Michigan. Chapters: 00:00 - Intro 01:00 - Bed sides 10:08 - Removing running boards 11:21 - Mounting spares 16:08 - Winch 27:11 - Exhaust work 30:09 - Fixing power steering 35:36 - Miscellaneous fixes/checks 38:15 - Interior cleanup 40:01 - Fixing the window 43:35 - Packing up 47:19 - Leaving home 50:06 - First stop for Repairs 53:11 - Through Wisconsin 58:49 - Illinois, more repairs 01:03:40 - Through Chicago 01:05:50 - Repairs 01:09:15 - Through Michigan 01:10:59 - Destination 01:12:13 - Repairs 01:14:42 - The Dunes 01:28:59 - Last stop 01:31:18 - Ferry ride across lake Michigan 01:35:33 - Last leg to home 01:36:48 - Home 01:37:40 - Cats
Not rated yetAutomatic → Manual
· 1 hr 34 min
- Turn on subtitles/CC's if you'd like explanations on what I'm doing throughout the video. - This is my Girlfriend's 1986 528e. Not the purple one, the silver one. The automatic transmission has been having intermittent issues for the past year, but it's always kept going until just recently. She got home with the car after a long roadtrip and immediately after, it stopped going forwards. We decided that instead of putting in another used automatic transmission, which would likely have issues soon enough, we'd swap in a 5 speed manual transmission. So, I picked up another 1986 528e in the next state over and brought it home. The car is a basket case with structural rust issues, and it's purple, but it has all parts for converting our car to a manual transmission. Chapters: 00:00 - Delivering the parts car 02:54 - Harvesting the 5 speed 11:35 - Disassembling the auto e28 22:17 - Installing the clutch pedal 32:37 - Swapping in a limited-slip differential 46:06 - Swapping radiators 48:59 - Rear main seal replacement 51:01 - 5 speed maintenance 54:24 - Another used 5 speed 01:00:26 - Installing clutch 01:02:20 - Installing the 5 speed 01:05:52 - Fixing/installing the shifter 01:12:13 - Driveshaft/Exhaust/Final installations 01:16:50 - First Start 01:18:29 - Finishing touches 01:20:57 - First Drive 01:25:24 - Parts car wrap up 01:31:12 - Cats
Not rated yet1973 Station Wagon.
· 1 hr 46 min
- Turn on subtitles or view the transcript at the bottom of the description if you'd like explanations on what I'm doing throughout the video - I just bought this 1973 Mercury Montego MX, a full-size station wagon. The car has been in the same family since new and it spent most of its life out in Montana until it was moved here, where it's been sitting as you see it for about 10 years. Though it hasn't ran for a couple decades. I anticipated this to be a pretty easy project, compared to other ones, as it hasn't sat for that long and it's not nearly as rusted. Turns out I was wrong as the 351 Cleveland engine was more stuck than any motor I've dealt with. After much persuasion, I got it running and driving once again. I like station wagons. Chapters: 00:00 - Getting it home 06:33 - First look at the engine, rusted spark plugs, sticky valves. 11:22 - Will it spin? No 12:26 - 1st attempt to un-seize the engine. 17:09 - Disassembling the engine 22:39 - 2nd attempt to un-seize the engine 24:20 - 3rd attempt to un-seize the engine 27:25 - Engine un-seized. 30:50 - Preparing parts for re-assembly 42:27 - Re-assembling the engine 52:46 - First start 56:30 - Pressure washing 1:02:59 - Tailgate 1:05:24 - Cleaning the interior 1:19:00 - Finishing assembly of the engine. 1:24:00 - Fuel system 1:26:42 - Exhaust 1:29:23 - Brakes 1:32:22 - Oil change 1:33:33 - Startup and checks 1:35:10 - Finishing touches before driving. 1:37:02 - Driving it 1:43:30 - Cats
Not rated yetBuilding The Ultimate Ford
· 2 hr 10 min
- Turn on subtitles/CC's if you'd like explanations on what I'm doing throughout the video. - Last time (https://youtu.be/igSk_-cGGCY), I got this lifted 1975ish F-150 running and driving, haphazardly, after it had sat for about 30 years. This truck is too far gone to return to the road, but after stress testing it off- road, I want to continue building it up into mudding truck/all purpose 4x4 rig. I got rid of the very tired 351m for a strong running 400 and did away with the rotted out bed for a roll cage. Along with a handful of other maintenance, this truck is now reliably the most fun I've ever had in a vehicle. Chapters: 00:00 - Getting it home 04:26 - Removing the bed 07:43 - Removing the engine 19:50 - Bigger engine 24:50 - Swapping oil pans 37:10 - Prepping the rest of the engine 42:08 - Torque converter seal 43:27 - Fitting headers 45:13 - Installing the 400 50:53 - Dipstick fix 52:46 - Installation continued 54:11 - Intake & Carb, finishing touches 1:00:23 - Exhaust fabrication 1:02:48 - First start 1:03:29 - Patching the radiator 1:06:18 - Engine finished 1:07:37 - Scrapping 1:13:09 - Fabricating a Roll Cage 1:22:45 - Radiator replaced, other stuff 1:26:08 - Wheel cylinders + Brake pads 1:33:55 - Replacing front axle U-joints 1:48:02 - Replacing leaf spring hanger 1:51:14 - Adding brake lights 1:53:57 - Trip to the venue 1:58:23 - Final drive, Mudding. 2:05:14 - Troubles on the way home 2:07:47 - Cat x2
Not rated yetMud Truck
· 2 hr 0 min
- Turn on subtitles/CC's if you'd like explanations on what I'm doing throughout the video. - I paid $500 for this 1975 (amongst a mix of parts from other years) F150. Back in 1984, it was a beautiful customized pickup truck, tricked out with things like a $1000 cassette stereo and hand painted pin-stripping. Now, it's mostly rust. My goal was to get it driving home within one day of work after it having been parked since the 90's. After accomplishing that, I began turning it into a dedicated off-road rig, a Mud Truck, if you will. Although I didn't find any mud in this video, this thing took one heck of a beating and is ready for more, almost. It will be enjoyed to its fullest potential and then some. Chapters: 00:00 - Will it run? 11:32 - Will it move? 15:13 - Will it stop? 20:27 - Time to drive it home 24:17 - The drive home 27:17 - Died in the driveway 29:51 - Going back for a couple things 32:05 - Cleanup 34:56 - Crystal Blue Persuasion 36:40 - Interior detailing continued 39:35 - Pressure washing 45:23 - Fuel system 55:32 - Carburetor rebuild 1:02:36 - Exhaust work 1:06:42 - One thing after another 1:15:50 - Cab mounts & Floors 1:28:01 - Oil change, Brakes, finishing touches 1:42:58 - New wheels and tires 1:46:52 - 80 miles to go 1:48:23 - Final drive 1:57:59 - Cat
Not rated yet1962 Chevrolet Nova, Clean-up And Repairs
· 1 hr 43 min
- Turn on subtitles/CC's if you'd like explanations on what I'm doing throughout the video. - Part 1: https://youtu.be/37FJXRjg_9Y?si=kemRcTsAjUBuPDfQ - This is the part 2 on the 1962 Chevy Nova I recently bought. Like most things I own, it needs rust repair. Admittedly, I did not realize how bad it was when I bought it, let's just say I overpaid a bit. Fortunately, these are pretty easy to find sheet metal for so I bought all the floors pans, though I did choose to fabricate a frame rail section from scratch. I also did some maintenance along the way and cleaned up the interior with some new pieces. My girlfriend thinks this car is cute, so i'm inclined to hang onto it for a bit. Chapters: 00:00 - Clean-up/teardown 10:46 - Fabricating a frame rail 30:16 - Floor pan replacement 48:54 - Newport differential 51:38 - Sealing/painting the floors 54:41 - Fuel tank + other maintenance 1:04:11 - Mounting the seats 1:13:21 - New carpet, final install of the seats 1:17:49 - New wheels and tires (used) 1:21:24 - Pressure washing 1:23:49 - Cleaning up the interior and re-assembly 1:32:20 - Lights 1:34:59 - Driving 1:41:14 - Cat
Not rated yet1962 Chevrolet II, Nova.
· 1 hr 46 min
- Turn on subtitles/CC's if you'd like explanations on what I'm doing throughout the video. - This is a 1962 Chevrolet II, Nova 400. The owner bought it back in the early 1970s for $75 just because he wanted the radio out of it. I asked if he had ever driven it and he simply said yes, he'd driven it around. Then I asked when the last time it ran was. To that, he said something along the lines of, "well, back in 1972 was when I parked it, took the key out, and it's been sitting since then". So, it's now been 53 years since the car has been on the road let alone the engine having ran. The car was originally from South Dakota but has been trailered around a few times since then until spending the last couple decades under this house, where I bought it from. Chapters: 00:00 - Getting it home 06:17 - First look 07:32 - Seeing if the engine spins 09:07 - Un-seizing the engine. 11:40 - Checking the valves 12:41 - Putting in a battery 14:30 - Trying the starter, oil pressure check 17:18 - Cleaning the carburetor 23:54 - Getting spark 26:15 - First start attempt 1 27:20 - Attempt 2 28:30 - 24 volts 30:35 - First start 31:45 - 12v start w/ fuel 35:04 - Cooling system repair/flush 37:50 - Oops, replacing the starter 42:11 - Cooling system, continued. 44:24 - Transmission/clutch test 45:19 - Replacing tail shaft bushing/pinion seal 51:43 - Fabricating exhaust 01:00:42 - Fluid change/check 01:02:41 - Brakes 01:28:11 - Tires 01:31:04 - Finishing touches 01:33:13 - First drive 01:37:15 - Overheated 01:42:27 - Made it home 01:44:52 - Cat
Not rated yetThe Mopar
· 2 hr 25 min
- Turn on subtitles/CC's if you'd like explanations on what I'm doing throughout the video. - This is 1970 Chrysler Newport. It's been in the same family since it was new but like many of the same, it had been left to sit for a long while, until recently. It was revived and had a handful of hot rod-esque work done to it. However, that seems to have now left it with an engine that smokes profusely and a transmission that slips severely, amongst a host of other questionable "modifications". My hope is to bring the car a little bit closer to stock form where it can just be enjoyed as the modest luxury automobile it once was, + rust. Chapters: 00:00 - The issues 03:20 - Compression test 06:06 - Removing the cylinder head. 10:28 - There's the problem 11:02 - Removing the engine/transmission 20:33 - Used drivetrain, unknown condition 23:03 - Will it run? 33:27 - Compression test on the new engine 36:34 - Degreasing/pressure washing 40:40 - Pulling parts off 45:30 - Painting 46:47 - Prepping the engine for installation 1:00:58 - Transmission service 1:08:51 - Cleaning up the engine bay, removing EFI 1:17:42 - Installing the engine/transmission 1:28:23 - Fabricating new exhaust 1:39:38 - Intake/carburetor 1:45:14 - Hooking things up 1:51:38 - Throttle/tv cable 1:55:24 - Final touches 1:58:35 - First start 2:03:24 - Cleaning up the interior, kinda 2:07:07 - First Drive 2:12:51 - Old pictures of the car 2:16:31 - Back to the 50's car show 2:23:07 - Cat
Not rated yetFixing Up A 1971 Honda CL450
· 1 hr 35 min
- Turn on subtitles/CC's if you'd like explanations on what I'm doing throughout the video. - A friend recently reached out to me and asked if wanted to pick some stuff out of storage unit he was clearing for a deceased relative. When I got there, I was surprised to see this 1971 Honda CL450 sitting in the corner. Its last registration was 1976 and it appears to have been sitting indoors, untouched, not running for decades. It's unbelievable to think that this bike was parked just 5 years after it was brand new, but a few factors suggest that it was ridden hard for those few years and then parked from some minor damages. At least that's my best guess. Chapters: 00:00 - First look 01:12 - Disassembly 07:53 - Carburetor rebuild 11:33 - Cleaning a rusted/varnished gas tank 12:50 - Carburetor install/Battery/Spark 16:43 - Gas tank cleaning continued 19:58 - Rebuilding the petcock 26:16 - First start + adjustments 30:12 - Adjusting the valve lash 35:35 - Setting the ignition timing 39:21 - Oil change 41:22 - Removing the wheels 42:40 - Changing the tires 48:43 - Reinstalling the wheels 50:28 - Adjusting chain tension 51:12 - Reinstalling the covers/seat/filters 53:30 - Fixing the loose shifter with worn splines 56:48 - Fixing crooked handlebars 57:32 - Other crash damage repairs 59:14 - Light check/electrical fixes 01:03:06 - Final checks 01:05:28 - First ride 01:12:40 - Torino transmission repair. 01:30:02 - Torino drive 01:32:40 - Cat
Not rated yetBig Free Boat, Continued.
· 2 hr 11 min
- Turn on subtitles/CC's if you'd like explanations on what I'm doing throughout the video. - Part One: https://youtu.be/jqT3C6TpIbs - Last week we got this engine running after it was seized and full of water. While it does run, it makes noise and smokes a lot. While I attempted to keep it going with some more repairs, it did not go as planned. After tearing it down and looking closer, I ended up replacing the Mercruiser 351w with a used 1994 OMC 302w. Once that was done I replaced some of the rotten floors and reinstalled the 1976 leather interior before taking back down the Mississippi River for a much smoother ride. Chapters: 00:00 - Previously 01:04 - Compression test 03:55 - Revisiting the lifter tick. 08:00 - Ant infestation 12:37 - Lifter repair continued (failed) 14:58 - Replacing the lifters 19:36 - Camshaft break-in first attempt 20:33 - Replacing the water pump, again 28:38 - Camshaft break-in second attempt 30:43 - Uh oh 31:16 - How bad did I damage the engine? 33:38 - Removing the engine 49:31 - Tearing down the engine 54:49 - There's the problem(s) 57:36 - $500 engine, will it run? 1:00:47 - Swapping parts over 1:09:04 - Installing the engine 1:25:44 - Fixing leaky outdrive 1:30:21 - Installing the outdrive 1:31:50 - First checks on the new engine 1:36:49 - Patching the floors 1:51:32 - Reinstalling the interior 1:54:00 - Finishing touches 1:59:00 - Lost the trailer 2:00:59 - On the water 2:08:49 - Cat
Not rated yetBig Free Boat.
· 1 hr 49 min
- Turn on subtitles/CC's if you'd like explanations on what I'm doing throughout the video. - I've never worked on a boat before, nor do I have much experience with one in any sense, but this one came up on Facebook Marketplace for free so I had to have it. It's a 1976 Webbcraft with a Mercruiser 5.8 (Ford 351 Windsor). It has been off the water for somewhere near two decades and for almost that entire time, the engine was sitting uncovered and collecting rainwater down the carburetor. Despite being locked up solid, it did free up and run. By the end of the video, the boat successfully made it down the Mississippi river. The engine probably needs a rebuild if I expect it to go any further. Chapters: 00:00 - Getting the boat out. 06:22 - Clearing out some of the trash 11:30 - Engine's full of water 13:40 - Un-seizing the engine. 16:19 - Removing the valve covers 18:00 - More water in the oil 20:28 - Piles of rust down the intake manifold. 22:48 - Compression test, bad. 25:25 - Carburetor rebuild 31:42 - Getting ready to fire it up 36:04 - First start 38:24 - Getting the fuel system to work 44:43 - Running it for longer 47:28 - Stuck lifters and no oil flow 49:20 - Removing the intake manifold 51:40 - Removing the lifters. 54:12 - Disassembling and fixing the lifters. 1:01:14 - Putting the engine back together 1:08:27 - Starting it up again 1:10:30 - Water pump replacement, lower unit. 1:17:43 - Cleaning and vacuuming 1:23:01 - Pressure washing 1:29:09 - Trailer lights/wiring 1:32:00 - Getting ready for the water 1:36:27 - Maiden Voyage. 01:46:43 - Cat
Not rated yetBig Block Torino Upgrades/Repairs.
· 1 hr 25 min
- Turn on subtitles/CC's if you'd like explanations on what I'm doing throughout the video. - This is my 1974 Gran Torino that I've swapped out the 302/FMX for a 460/C6. The drivetrain came from an extremely rusted out '78 Grand Marquis that was left in a field for a couple decades. Although the engine runs like new, the transmission did not last long. It's definitely not due to the fact that i ran it dry of fluid and neutral dropped it a few times in an attempt to free up the brakes in the Marquis. I picked up a junkyard transmission to replace it and also installed a 9 inch Limited slip axle as an upgrade over the 8 inch open diff. Lastly, I installed the proper big-block springs up front and then covered some work on my girlfriends 1986 BMW E28, as I may have made a mistake when rebuilding the cylinder head. Chapters: 00:00 - Bad transmission 01:11 - Removing the transmission 06:56 - Preparing the used transmission 10:57 - Installation 20:16 - Test drive, had issues. 24:32 - Limited slip differential rebuild 35:48 - 9 inch axle cleaning/painting 41:47 - Removing the 8 inch axle 46:37 - Installing the 9 inch 50:55 - Brake job 58:40 - Installing bigger front coil springs 1:10:11 - Driving + limited slip testing 1:15:32 - BMW head gasket leak fix 1:24:14 - Cat
Not rated yet1966 Ford F100, Clean-Up And Repairs.
· 1 hr 37 min
- Part 1: https://youtu.be/nE0_EruRl8I - Turn on subtitles/CC's if you'd like explanations on what I'm doing throughout the video. - In the last video we got this 390 FE+ 4 speed toploader F100 running and driving after it had been sitting in a field for 40 years. This time we do some clean up and repairs throughout the truck, patching the floors, fixing the wiring, doing some repairs on the engine and more. Chapters: 00:00 - Intro 00:28 - Disassembly 02:58 - Cleaning out mouse nests/pounds of dirt. 07:48 - Fixing the wiring mess 17:38 - Getting the fuel system working 25:11 - Installing a high volume oil pump 34:14 - Cab mount replacement 40:56 - Painting the wheels 44:49 - Cab mount replacement continued 51:14 - New floor pan 1:00:48 - New wheels and tires 1:01:46 - Pressure washing the interior 1:04:20 - Reassembling the interior 1:06:54 - More rodent cleanup 1:10:55 - Getting a hood back on it 1:20:27 - Pressure washing the outside 1:26:33 - Lights 1:28:28 - Hole in the oil pan 1:29:40 - Finishing touches 1:30:25 - Driving 1:32:00 - Broke down 1:34:14 - Fixed 1:36:14 - Cat
Not rated yet1966 F100, Hurst Equipped
· 1 hr 56 min
- Turn on subtitles/CC's if you'd like explanations on what I'm doing throughout the video. - This is a 1966 F100, but it's indeed much more than just that. Back in the 1970's this thing was hot rodded with a 390 v8 and the famous wide - ratio Toploader four speed out of a Ford car. Shortly thereafter, in the early 80's, it was parked in a field for 40 years before it was purchased by the gentleman I bought it from, he got it and had hopes to work on it but never got around to doing anything with it. He did tell me that the engine is likely junk, indicative by the fact that the headers are near completely rusted off, the oil pan was filled with water and the cylinders full of rust. Nonetheless, let's give this engine the benefit of the doubt. Chapters: 00:00 - Bringing it home 03:10 - First look under the hood 05:16 - Rusted cylinders, cleaning the engine, removing rocker shafts 10:12 - Is it seized? 12:13 - Servicing the valve train 16:29 - Battery 18:09 - Water in the oil 19:23 - Trying the starter, building oil pressure, testing compression 23:14 - Carburetor, seized. 31:01 - Getting spark 34:14 - Reinstalling the valve covers 36:08 - First start attempt 37:00 - 24 Volts 40:27 - Getting closer 41:56 - First start 42:41 - Running it to RPM, freeing up the piston rings. 45:24- Troubleshooting rough running 47:22 - Will it start on 12 volts? 47:52 - Replacing the rusted out headers 55:30 - Fabricating an exhaust system. 1:00:57 - How's it sound now? Great. 1:01:49 - Oil change and coolant flush 1:09:31 - Getting parts from the junkyard 1:11:22 - Installing the driveshaft 1:12:50 - Testing the 4 speed. 1:14:37 - Brakes 1:37:58 - Greasing/fluid check 1:39:30 - Tires 1:40:55 - Shifter handle fabrication, seat install 1:44:06 - Getting ready for the road. 1:47:47 - First Drive 1:54:20 - Cat
Not rated yet1973 AMC Javelin, Major Repairs
· 1 hr 23 min
- Turn on subtitles/CC's if you'd like explanations on what I'm doing throughout the video. - I recently got this Amc Javelin running again (https://www.youtube.com/watch?v=_c0axKtH2bA&t=456s) to find that the transmission was stuck in forward gear, no matter the position of the shifter. As much as I wanted to just throw in a used transmission, or put in a 4 speed, the parts proved too hard to find in a timely manner. I ended up rebuilding the transmission and fixing the issue, which was the forward clutches being fused together. The car is now listed for sale, but if it doesn't sell at the current price, I'll hang onto it and do some more repairs that you'll see on the channel. Chapters 00:00 - Recap of the transmission issue 1:30 - What's in the pan? 3:00 - Removing the transmission 6:31 - Degreasing 7:47 - Disassembly 10:17 - Here's the problem 11:38 - Disassembly continued 18:48 - Rebuilding the transmission 53:36 - Reinstalling the transmission 1:02:13 - Does it work? 1:05:10 - Installing the bumper 1:08:51 - Going for a drive 1:12:29 - At the junkyard 1:19:04 - Plane 1:22:45 - Cat
Not rated yet1973 AMC Javelin.
· 1 hr 25 min
- Turn on subtitles/CC's if you'd like explanations on what I'm doing throughout the video. - I bought this 1973 AMC Javelin from a local towing company, the same place that sold me the '74 Torino. This one looks to have been someone's unfinished project and I imagine it's been off the road for about a decade, the last registration was 2014. On top of not running just from sitting, it's also missing a carburetor, ignition components, and was left with a handful of pieces unbolted. Nonetheless, the 360 v8 has a few upgrades, so it should be fun. Also, it's the least-rusty vehicle I've worked on in a while. The floors are more solid than anything around here. Chapters: 00:00 - Getting it home 02:42 - First look under the hood 04:05 - Seeing if it cranks over 06:28 - Carburetor 14:32 - Getting spark 17:56 - First start preparations 19:50 - First start 21:57 - Sorting out the fuel system 24:49 - Only running on 4 cylinders 26:50 - Getting it to run on 8 cylinders 34:14 - Now it sounds like a v8 35:06 - Fixing the dipstick tube broken off in the block 39:32 - Oil change 40:56 - Cooling system 42:28 - Tuning the engine 45:15 - Flushing the cooling system 46:42 - Unlocking the steering column/shifter 51:11 - Un-seizing the wheel. 55:19 - Replacing a valve stem without a tire machine 57:03 - Fixing the brakes 1:06:52 - Tightening things down, etc. 1:10:21 - Quick clean-up, seat cover removal 1:13:46 - Finishing touches 1:16:44 - Transmission issues 1:18:44 - First Drive 1:24:03 - Cat
Not rated yet